Tube filling sealing machine semi automatic soft tubes filler online with ultrasonic tail sealing equipment customized cream plastic tube packing

Saturday, January 26, 2019

Tube filling sealing machine semi automatic soft tubes filler online with ultrasonic tail sealing equipment customized cream plastic tube packing

Description:

Model:GP-T009

Power Supply 220V/50HZ/Single phase
Power 1500w
Frequency 20Khz
Tube Length 40-280mm
Tube Diameter 10-80mm
Filling volume A:5-30ml B: 6-60ml C: 10-120ml
D: 25-250ml E: 50-500ml (Optional)
Size 735*670*1300mm
Weight 130kg
Model GP-T009 single head filling Machine inline with ultrasonic sealing machine function and application

1.Use ultrasonic to weld plastic soft tube tail. Do not need any adhesive or filler or solvent when welding, do not consume large amounts of heat, and easy to operate, high welding speed, high efficiency.
2.This machine is widely used in toothpaste, cosmetic, medical product, food and industrial tubes etc.
Main parameters of simple inline filling sealing machine tubes filler sealer semi automatic:

Model GP-T009
Power Supply 220V/50HZ/Single phase
Power 1500w
Frequency 20Khz
Tube Length 40-280mm
Tube Diameter 10-80mm
Filling volume A:5-30ml B: 6-60ml C: 10-120ml D: 25-250ml E: 50-500ml (Optional)
Size 735*6701300mm
Weight 130kg
► Sealing Machine layout

1.Main body 2.Sensor 3.Tube Hight adjustment 4.Front mould 5.Back mould 6.Cutter
7. Gas-pressure meter 8.Gas-pressure adjustment 9.Emergency button 10.Start button
11.PLC 12.Holder 13.Moulds gap adjustment 14.Power lamp 15.Power switch
17.Tune 18. OSC check 19.Over load lamp 20.Loading meter
(Remark: Pls checking the Front mould Screw if with strong lock, as Afraid when the transportation and screw is loose)
Machine actual in stock ultrasonic tube sealer:

►PLC
1.Press to English to next page , and press Auto to manual

►Sealing part
Motor start : this is for control the Tube holder running
Feeding cylinder start: this is for control the Tube holder feeding
Ultrasonic cylinder start: this is for control the up mould and down mould working.
Trimming cylinder start: this is for control the cutter
Fill Cylinder : This is for control the Filler head cylinder star or Stop when manual
Fill start: This is for control the filling star or stop when manual
Ultrasonic start: This is for control the frequency, this is same as the “18. OSC check”
Tube Orientation on : this is for control the Sense off/on
Time setting: This is for Adjusting the Delay time/ Welding time/Holding time
Delay time : 0.80
Welding time: Tube Dia 20,the time will about: 0.20,
Tube dia 30,the time will about 0.40
Tube dia 40, the time will about 0.50
Tube dia 50, the time will about 0.7
Holding time: 0.35
►Filling part

►Operation process

1.Connect power and compressed air correctly (suggest 0.5MPa).
2. Press the Power switch
3. Press ‘OSC check’ button and set ‘Tune button’ at the same time, Pls using the screw on the Tune button, you can turn to Left or Right, while find the minimum of ‘Signal light’ (it will about low than 1A) fixed ‘Frequency adjustment’. (do not press ‘OSC check’ continuously, press it intermittently)
4.Put tube on the holder.
5.Press ‘Ultrasonic cylinder start’, front mould and back mould will be closed. set ‘Moulds gap adjustment’, let two moulds just touch and no gap. Press ‘Cutter controller’ and confirm the cutter will work smoothly.(need to put the plastic tube on the tube holder when you adjusting)
6.Set front mould and back mould and cutter at original position.
7.Put tube on the ‘Holder’ and press ‘Feeding cylinder start’, the tube will run between two moulds. Adjust the height of holder if necessary. (suggest tube is higher than back mould 2 to 3 mm)
8.Make tube back to original position.
9.Set to auto status, turn on sensor if tube has color code otherwise turn off it.
10.Press ‘Auto’ the machine will work automatically.
Remark: Pls also read the machine install video for reference !!!!
►Tubes filling-sealing samples