Description:
Automatic rings sealing machine Rotary glass jars sealer equipment with caps lifter feeding system rotary capper equipment
Model:GP-AC05
Speed: 20pcs-40pcs per min
Rated voltage: 110Ｖ/60Hz(USA market customized)
Machine Power: 800Ｗ
Exterior dimension: About 2300*1800*1800 MM (L*W*H)
Air Pressure: 0.7-1.0 MPa
Weight: About 400 Kg
Speed: 20pcs-40pcs per min
Rated voltage: 110Ｖ/60Hz(USA market customized)
Machine Power: 800Ｗ
Exterior dimension: About 2300*1800*1800 MM (L*W*H)
Air Pressure: 0.7-1.0 MPa
Weight: About 400 Kg
The whole automatic capping machine adopts elaborate DIY design.By eliminating unnecessary complex and heavy machinery, it adopts suit type assembly.The maintenance and servicing can be completed without professionals.when it is necessary to replace the product,just make some simple adjustments, it can be immediately put online for production.
The machine is suitable for capping various types of round bottles in such industries as food, condiment,medicine,wine,oil and cosmetics etc.
Drawing for model GP-AC05 rings sealing machine :
Drawing for model GP-AC05 rings sealing machine :
Basic parameter of model GP-AC05 rotary sealing machine for glass jars:
Model:GP-AC05
Speed: 20pcs-40pcs per min
Rated voltage: 110Ｖ/60Hz(USA market customized)
Machine Power: 800Ｗ
Exterior dimension: About 2300*1800*1800 MM (L*W*H)
Air Pressure: 0.7-1.0 MPa
Weight: About 400 Kg
Model:GP-AC05
Speed: 20pcs-40pcs per min
Rated voltage: 110Ｖ/60Hz(USA market customized)
Machine Power: 800Ｗ
Exterior dimension: About 2300*1800*1800 MM (L*W*H)
Air Pressure: 0.7-1.0 MPa
Weight: About 400 Kg
Notification before Operation of the rotary sealing machinery
1: Before the machine is plugged in, make sure the power switch is in the closed state, and then follow the instruction.
2: If the machine does not run in a long time, it should be wiped with a piece of dry cloth and must not be cleaned with any corrosive cleaning agent.
3: It is strictly prohibited to spurt any liquid into the electric box of the machine, so as to avoid corrosion to the internal electrical components and cause short circuit.
4: Check according to the equipment packing list models, specifications and quantity of the equipment and materials to make sure that they meet the requirements of design and product standards and accompanied by certificates of conformity.
5 : Check the appearance of the equipment to make sure that it is free from any deformation, damage and corrosion, and all spindles that they should be flexibly rotating without any blockage.
6 : This machine is working under single phase AC 110V, and the flat 3-legged power plug should be plugged into the power socket with a ground wire.
How to operate the model GP-AC05 rings sealing machine glass bottles capper equipment:
Press the "Power Button" and the touch screen shows as follows:
1: Before the machine is plugged in, make sure the power switch is in the closed state, and then follow the instruction.
2: If the machine does not run in a long time, it should be wiped with a piece of dry cloth and must not be cleaned with any corrosive cleaning agent.
3: It is strictly prohibited to spurt any liquid into the electric box of the machine, so as to avoid corrosion to the internal electrical components and cause short circuit.
4: Check according to the equipment packing list models, specifications and quantity of the equipment and materials to make sure that they meet the requirements of design and product standards and accompanied by certificates of conformity.
5 : Check the appearance of the equipment to make sure that it is free from any deformation, damage and corrosion, and all spindles that they should be flexibly rotating without any blockage.
6 : This machine is working under single phase AC 110V, and the flat 3-legged power plug should be plugged into the power socket with a ground wire.
How to operate the model GP-AC05 rings sealing machine glass bottles capper equipment:
Press the "Power Button" and the touch screen shows as follows:
It is the boot picture and also the picture to select an operation language:
Click "English" to enter the following picture:
The picture also has the following functions:
1, Start up the equipment. When the equipment is in the normal standby mode, click manual and then it shows
"AUTO" equipment is in a readiness state, then clickstart.jpg, and the equipment will be in an operation state.
Note: if the equipment is still in the standby state, check the prompt below the screen, eliminate the alarm as required and then it will be normally started.
2, Output setting, output zero clearing. Click clear.jpg to clear the current output and the equipment will be started counting from 0.
3, Empty the remaining materials on the turntable. After the completion of the products to be completed, if there are still remaining materials in the turntable, click operation.jpg to clear bottles in the turntable.
"AUTO" equipment is in a readiness state, then clickstart.jpg, and the equipment will be in an operation state.
Note: if the equipment is still in the standby state, check the prompt below the screen, eliminate the alarm as required and then it will be normally started.
2, Output setting, output zero clearing. Click clear.jpg to clear the current output and the equipment will be started counting from 0.
3, Empty the remaining materials on the turntable. After the completion of the products to be completed, if there are still remaining materials in the turntable, click operation.jpg to clear bottles in the turntable.
Click operation.jpg to enter the following picture.
This column screen is for manual debugging
Only when screen shows “Man”, buttons in the picture are valid.
Click Parameter to enter the following picture:
This picture is used for setting of the process parameters.
Incoming bottles detection time: when bottles are induced in the bottle-mouth, delay the time before the cylinder moves to block later bottles.
Glanding time: when the caps are pressed on the bottle mouth, stay at the time and loosen up.
Cap locking time: when the cap locking motor is pressured on the bottle mouth, stay at the time and loosen the motor up.
Alarm and trouble-shooting method:
1、Emergency stop has been pressed. Push the emergency stops on the machine cap and next to the touch screen.
2、The output reaches the set value. Set the output, press the clear button to clear the current output.
3、When caps are not detected for a long period of time, please check. Check the bottle cap induction fiber as to whether it is well provided. Check whether caps are in place or not.
4、When bottles are not detected for a long period of time, please check. Check as to whether bottles are in place.
Electric eye adjusting:
This column screen is for manual debugging
Only when screen shows “Man”, buttons in the picture are valid.
Click Parameter to enter the following picture:
This picture is used for setting of the process parameters.
Incoming bottles detection time: when bottles are induced in the bottle-mouth, delay the time before the cylinder moves to block later bottles.
Glanding time: when the caps are pressed on the bottle mouth, stay at the time and loosen up.
Cap locking time: when the cap locking motor is pressured on the bottle mouth, stay at the time and loosen the motor up.
Alarm and trouble-shooting method:
1、Emergency stop has been pressed. Push the emergency stops on the machine cap and next to the touch screen.
2、The output reaches the set value. Set the output, press the clear button to clear the current output.
3、When caps are not detected for a long period of time, please check. Check the bottle cap induction fiber as to whether it is well provided. Check whether caps are in place or not.
4、When bottles are not detected for a long period of time, please check. Check as to whether bottles are in place.
Electric eye adjusting:
1. Amplifier structure
1.Optical fiber lock bar 2.Operating status indicator
3.Set
3.Set
4. DSC indicator light
5.Digital monitor 6.Manual button
7.Extended protection cover 8.Expansion connector
9.Power Selector Switch 10. Mode button
11.Output selector 12.Cables
13.Dust protector 14.Set value (In green)
15.current value (In red)
Working process for the fiber optical setting:
Step one: When the electric eye falls in the gap, the red current value is 144.
Step two: When the electric eye falls on the label, the red current value is 4.
Step three: Adjust the set value",about 1/2 of the value that the electric eye is on the body paper (in the gap between the objects to be detected) and the value that the electric eye is on the paper
the set value is (144+4)/2=74, adjust the manual button to adjust the set value to be 74.
Step four: Move the label gap back and forth in the electric eye location and the red “signal light/indicator light”.
Circuit description:
5.Digital monitor 6.Manual button
7.Extended protection cover 8.Expansion connector
9.Power Selector Switch 10. Mode button
11.Output selector 12.Cables
13.Dust protector 14.Set value (In green)
15.current value (In red)
Working process for the fiber optical setting:
Step one: When the electric eye falls in the gap, the red current value is 144.
Step two: When the electric eye falls on the label, the red current value is 4.
Step three: Adjust the set value",about 1/2 of the value that the electric eye is on the body paper (in the gap between the objects to be detected) and the value that the electric eye is on the paper
the set value is (144+4)/2=74, adjust the manual button to adjust the set value to be 74.
Step four: Move the label gap back and forth in the electric eye location and the red “signal light/indicator light”.
Circuit description:
Production inspection on scene:
Wooden case packing for rings sealing machine automatic Model:GP-AC05
http://gearpackaging.com/
Contact:Tony
Cellphone:+86-188-1682-5234
Telephone:+0769-8270-8461
Skype:Gearpacakaging Tony
E-mail:gearpacking@gmail.com
Hi, really appreciate you for this awesome article you have covered all the pin points of the topic in this article keep up the good work. Cheers!
ReplyDeletePowder Packing Machine