Electronics cables wiring flags folding labeling machine semi automatic with customized feeding positioning system sticker labeller customized equipment

Description:

Electronics cables wiring flags folding labeling machine semi automatic with customized feeding positioning system sticker labeller customized equipment

Model:GP-CLM02
Applicable label parameters: label roll diameter 1.5〞-2.0",
outside diameter MAX200mm; (other specifications need to be customized)
Label material: PVC, PET, cloth, paper, etc.
Label specifications L*W:25*10mm Minimum; Max: 100*50MM
Labeling accuracy: ± ≤ 0.5MM
Capacity: 800PCS-1000/H or more;
Dimensions(mm): 1126L*600W*1136H;
Machine weight: 70KG Package weight: 85KG
Applicable wire harness: wire outer diameter MAX4mm MIN3mm;

This labeling wire cables machine is used for the folding and labeling of wiring cables,harnesses flags and round bars in the electronics industry.
Notice before using the wire labeling machine model GP-CLM02:
►Make sure the power supply voltage (AC220V) and the air pressure 4-6kgf before power on, and the external power supply must be grounded reliably.
►Do not block the chassis cooling holes.
►Non-professional technicians are strictly prohibited from opening the chassis.
►When the device is in operation, physical contact with the movement range is strictly prohibited.
►When the equipment fails, the power switch should be turned off first, and it is forbidden to carry out maintenance.
Technic Performance of model GP-CLM02 labeling machine

Model GP-CLM02

Applicable label parameters: label roll diameter 1.5〞-2.0",
outside diameter MAX200mm; (other specifications need to be customized)
Label material: PVC, PET, cloth, paper, etc.
Label specifications L*W:25*10mm Minimum; Max: 100*50MM
Labeling accuracy: ± ≤ 0.5MM
Capacity: 800PCS-1000/H or more;
Dimensions(mm): 1126L*600W*1136H;
Machine weight: 70KG Package weight: 85KG
Applicable wire harness: wire outer diameter  MAX4mm  MIN3mm;
Labels final product wire labelled samples:

Wooden case package for DHL courier shipping of wire labeling machine model GP-CLM02:

Detailed instruction of how to operate wire flat folding labeling machine as below:
installation
►Move the device to the desired installation location.
►Adjust the positioning screw at the bottom of the device to make it smooth.
►Item list for controlling panel of wire labeller model GP-CLM02

Operation method
Clip adjustment as shown (a total of three groups of six) Loosen the locking screw and place the wire harness to be machined into the V-shaped groove under the crimping block. After the wire harness is tightened, tighten the screw.

Label installation and commissioning
First install the label to the delivery wheel set as shown below
 Note: The label must be passed through the label eye, and the label should be straightened and straightened.

Align the position of the label with the triangular mark of the label's sensor eye, press and hold the button on the eye until the electric eye begins to blink, then align the position of the unlabeled eye with the eye, and press the button to extinguish the blinking light;
Adjust the vacuum template according to the wire diameter reference scaleParameter adjustment
Turn on the power switch, as shown below
Switch the device to manual mode
Out of standard position: The value is proportional to the standard position. Adjust the position of the outbound label to match the peeling plate and transfer the label to the following position.





Speed setting

Click on the speed settings to enter the speed settings page as shown below, according to the operating habits can be set.
If the accuracy is higher, please reduce the speed of the motor.
Positioning settings
Click on the positioning settings to enter the positioning settings page as shown below

Fitting motor parameters in detail
Fit the first move angle: the first move angle of the target before it is pasted
Binding contract dynamic angle: the angle of synchronization of the target plate at the time of affixing and entering the line, this value will affect the tightness of the label and the wire.
Fit end point angle: The position of the target plate is fully fit in place, the value of the small label does not match, and the motor will overshoot if the value is too large.
Into the line motor parameters in detail:
The position of the contact surface of the clip and the label: the position of the contact between the wire and the label, the value of the small wire and the label cannot be contacted, and the label is not well-labeled; the large value line will press the label down and the label is not well-labeled; the proper position should be the wire The label just came into contact with as well
Sticking into the line angle: the position of the target when the target moves synchronously with the wire, the value of the small label is not tight; the value label will pull too tightly or pull the label
Tag tightening angle: When the target plate and wire synchronous action is completed, further tightening is performed; the value of the small label is not tightly attached; the value label is pulled too tightly or the label is pulled
Rotary motor parameters in detail:
Label left and right positions: When the label is left-shifted, the value is increased; when it is right-shifted, the value is decreased.
Rotation end point angle: The position of the target plate rotating out of the line clamp is to be a right angle; when the left side is smaller, the value is smaller; when the right side is right, the value is increased.

The wire diameter parameter changes with the wire diameter. The corresponding parameters in the wire are described as follows
Crimping and label contact surface position: Adjust the labeling parameters in manual mode so that the label and wire harness make contact as follows
The corresponding parameters of the tuning parameter settings are as follows
Rotary motor and inlet motor speed ratio: Correct the fit of the two motors, collision avoidance machine.
Fit motor parameters: Adjust the fit of the label to correct the error;
Rotating motor parameters: adjusting the rotary angle correction error of the vacuum chuck;
Centering adjustment (as shown below)

Loosen the locking screw, adjust the alignment lever so that the label is in the middle of the harness, and then tighten the screw.
Maintenance and Maintenance
Heavy pressure is strictly forbidden. Please keep it clean;
Lubricate the machine on schedule
One month plus one lubricant for the target's location
Three months inspection of the timing belt wear of various parts of the machine

http://gearpackaging.com/

Contact:Tony 

Cellphone:+86-188-1682-5234 

Telephone:+0769-8270-8461

Skype:Gearpacakaging Tony

E-mail:gearpacking@gmail.com